2008 BMW 328I PASSENGER DOOR HANDLE HOW TO

After a few years, even with reasonable care, it will be worn and become sticky. The rubber coating is supposed to last for a while. But, when it becomes too long for that heater to work, the rubber coating melts and becomes sticky. Sometimes we keep the heater on before getting in our BMW or after getting out to keep it warm. The rubber coating starts to melt when your BMW is facing that sunlight for a long time the rubber coating starts to melt. If you live somewhere like Florida or UAE, where half of the year is summer, you have likely seen direct sunlight in your BMW. Anyway, there are some reasons for the BMW door handle to melt, and those are given below.

6 Conclusion Why Does Your BMW Door Handle Become Sticky?īMW manufactures most of its car door handles with plastic, and the cover is made of rexine for lower-end models, and high-end cars use genuine leather for door handle covers.īut as a matter of fact, even genuine leather melts in certain situations.

5.4 What Are The Best Lubricants To Use For Getting Rid Of BMW Door Handles Stickiness?.

5.3 Who Can Repair A BMW Sticky Door Handle?.

5.2 Does Lubricant Help To Remove Stickiness From BMW Door Handles?.

5.1 Can I Use Superglue To Get Rid Of Sticky BMW Door Handles?.

4 How Can You Prevent BMW Door Handle Melting?.

3 How Much Will It Cost To Repair Sticky BMW Door Handles?.

2008 BMW 328I PASSENGER DOOR HANDLE HOW TO

2 How To Get Rid Of Sticky BMW Interior Door Handles?.1 Why Does Your BMW Door Handle Become Sticky?.Try practising with a door you can open first so you get the feel of it. Lubricate the lot and keep using the door as I suspect it was seized by moiture or disuse and became stuck as the locking pin that you can feel delatch when you slowly open the door latch with either handle with the door open and using a finger to reset the latch each time. Maybe it also teaches the other jammed door what you want it to do? these cars are getting old and probably imprinting on the owners mentality, so be nice to it ) You cannot put it back in the hole in the door metal unless you take it apart as the two parts and put the base in before the cover. At first I levered out the whole port hole cover but found I should have done it as a two step process. Make sure you pull out the inner oval like section on this port hole as it comes out and then if you want to you can pull out the outer part of the port hole. I sprayed al parts with WD40 and removdd the little opening cover next to the lock on the normally concealed door edge to access into the lock area. Then I used my finger to operate the door lock clasp instead of closing the door again, and opened and closed the mechnism with both door handles many times to ensure it was working.

You can manipulate the inside and outside door handles while doing this trying to open the door.įinally it opened, no damage! I did scratch the window tint a liitle bit because i used a hacksaw blade but no big deal. After a while of doing this and feeling around with the tool. I used a hacksaw blade as a thin stiff insert between the window wound down and fully open and the inside rubber seal to get down to the locking mechanism at the rear of the outside door handle - thst is where you aim for, and then move the tool around feeling for a lever you can push down that is a mechanism that is springy and you can move. BUT then I found this and it worked for me. I read about making a hole in the door lining to break up the actuator and the risks with the air bag (DISCONNECT THE BATTERY FIRST AND LET THE CIRCUIT DISCHARGE FOR 15 MINUTES BEFORE MAUCKING ABOUT WITH THE EXPLOSIVE AIRBAG!!!), but was reluctant to do this but it seemed the way to go. I tried thumping against the inside and outside of the door to unjamb it. I tried multiple door handle operations inside and outside. I tried spraying WD40 or aerosol liquid lubrication into accesible areas. The lock indicator went up and down electrically/electronically via the actuator but the door would not open.

the passenger door seixed and could not be opened by internal or external handle. I had this problem with our 528i E39 1996.

2008 bmw 328i passenger door handle